Effect of pouring temperature on fluidity, porosity, density, and microstructure of Al-Si alloy in gravity die casting
DOI:
https://doi.org/10.47540/ijias.v6i2.2677Keywords:
Aluminium–silicon Alloy, Gravity Die Casting, Microstructure, Pouring Temperature, PorosityAbstract
The growing demand for lightweight aluminium components necessitates improved quality control in casting, particularly for aluminium–silicon (Al–Si) alloys produced via gravity die casting. This study systematically investigates the effect of pouring temperature on the fluidity, porosity, density, and microstructure of an Al–Si alloy using a gravity iron die mold with varying section thicknesses. Casting experiments were conducted at pouring temperatures of 600°C, 650°C, and 700°C to simulate thin-wall casting conditions. Fluidity was evaluated by measuring flow length, while density and porosity were determined using Archimedes’ principle. Microstructural evolution was characterized via optical microscopy. The results demonstrate that increasing the pouring temperature significantly enhances fluidity, enabling the complete filling of progressively thinner sections. However, higher temperatures also lead to increased porosity and reduced density, particularly in thicker sections, due to prolonged solidification times and reduced cooling rates. Microstructural analysis reveals that higher pouring temperatures and larger section thicknesses promote coarser α-Al dendrites, larger β-Si particles, and increased intermetallic phase aggregation; conversely, lower pouring temperatures and thinner sections result in finer, more homogeneous microstructures. These findings highlight the critical trade-off between mold-filling capability and internal casting quality, emphasizing the importance of optimizing pouring temperature in the gravity die casting of Al–Si alloys.
References
Al-Helal, K., Stone, I. C., & Fan, Z. (2012). Simultaneous primary Si refinement and eutectic modification in hypereutectic Al-Si alloys. Transactions of the Indian Institute of Metals, 65(6), 663–667.
Asghar, O., Franceschi, M., Ferro, P., & Bonollo, F. (2025). Development of New Aluminium Alloys for Future Automotive Structural Components With Less Criticality and Higher Casting Processability. International Journal of Metalcasting, March.
Bang, H. S., Kwon, H. I., Chung, S. B., Kim, D. U., & Kim, M. S. (2022). Experimental Investigation and Numerical Simulation of the Fluidity of A356 Aluminum Alloy. Metals, 12(11).
Bazhenov, V. E., Petrova, A. V, Rizhsky, A. A., Tselovalnik, Y. V, Sannikov, A. V, & Belov, V. D. (2021). Simulation and Experimental Validation of A356 and AZ91 Alloy Fluidity in a Graphite Mold. International Journal of Metalcasting, 15(1), 319–325.
Becker, H., Thum, A., Distl, B., Kriegel, M. J., & Leineweber, A. (2018). Effect of Melt Conditioning on Removal of Fe from Secondary Al-Si Alloys Containing Mg, Mn, and Cr. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 49(12), 6375–6389.
Campbell, J. (1988). Thin wall castings. Materials Science and Technology, 4(3), 194–204.
Chen, G.-C., & Li, X. (2024a). Effect of TiC nano-treating on the fluidity and solidification behavior of aluminum alloy 6063. Journal of Materials Processing Technology, 324, 118241.
Chen, G.-C., & Li, X. (2024b). Nanoparticle-Enhanced Castability of Aluminum Alloy 2024: Fluidity, Hot Cracking, and Surface Quality. Metallurgical and Materials Transactions A, 55(3), 761–773.
Choudhary, I. N., Sinha, N. K., Mahali, M., & Singh, J. K. (2024). Microstructure and Mechanical Behavior of Multidirectional Forge SIMA Process Al- Si Hypereutectic Alloy. Silicon, 16(8), 3583–3593.
de Medeiros, H. C., da Silva Franco, L. H., de Oliveira, D. F., Caluête, R. E., de Lima, B. A. S. G., Peres, M. M., & Brito, I. C. A. (2025). Influence of pouring and mold temperatures on microstructural behavior and microhardness of the Al-4.5Cu-0.5(Al-5Ti-1B) alloy obtained by unsteady-state directional solidification: An experimental comparative study. Journal of Alloys and Metallurgical Systems, 9(January), 1–11.
Di Sabatino, M. (2008). On fluidity of aluminium alloys. Metallurgia Italiana, 100(3).
Durmus, M., Dispinar, D., Gavgali, M., Uslu, E., & Çolak, M. (2025). Evaluation of Fe Content on the Fluidity of A356 Aluminum Alloy by New Fluidity Index. International Journal of Metalcasting, 19(3), 1590–1604.
Engler, O., & Knarbakk, K. (2021). Temper rolling to control texture and earing in aluminium alloy AA 5050A. Journal of Materials Processing Technology, 288(June 2020), 116910.
Ergün Songül, E., & Dispinar, D. (2025). Influence of Casting Route on the Microstructure and Mechanical Behavior of A360 Aluminum Alloy: A Process–Structure–Property Correlation. European Journal of Engineering and Applied Sciences, 8(2), 19–27.
Erzi, E., Yüksel, Ç., Gursoy, O., Çolak, M., & Dispinar, D. (2024). Characterisation of Aluminum Alloys by Octopus Fluidity Test. Politeknik Dergisi, 27(1), 21–25.
Ferreira, A. F., Chrisóstimo, W. B., Sales, R. C., Garção, W. J. L., & de Paula Sousa, N. (2019). Effect of pouring temperature on microstructure and microsegregation of as-cast aluminum alloy. International Journal of Advanced Manufacturing Technology, 104(1–4), 957–965.
Haga, T., Imamura, S., & Fuse, H. (2021). Fluidity investigation of pure al and al-si alloys. Materials, 14(18), 1–15.
Han, Q. (2022). A Model correlating fluidity to alloy variables in hypoeutectic alloys. Acta Materialia, 226, 117587.
Han, Q., & Zhang, J. (2020). Fluidity of Alloys Under High-Pressure Die Casting Conditions: Flow-Choking Mechanisms. Metallurgical and Materials Transactions B: Process Metallurgy and Materials Processing Science, 51(4).
Jahangiri, A., Marashi, S. P. H., Mohammadaliha, M., & Ashofte, V. (2017). The effect of pressure and pouring temperature on the porosity, microstructure, hardness and yield stress of AA2024 aluminum alloy during the squeeze casting process. Journal of Materials Processing Technology, 245(July), 1–6.
Jin, L., Liu, K., & Chen, X. G. (2020). Evolution of dispersoids and their effects on elevated-temperature strength and creep resistance in Al-Si-Cu 319 cast alloys with Mn and Mo additions. Materials Science and Engineering: A, 770(January).
Júnior, P. F., De Olivé Ferreira, L., Garcaõ, W. J. L., De Paula Almeida, R., Melo, C. M., & Ferreira, A. F. (2022). Heat-flow parameters affecting microstructure and mechanical properties of Al-Cu and Al-Ni alloys in directional solidification: An experimental comparative study. International Journal of Materials Research, 113(3), 181–193.
Khan, M. H., Das, A., Li, Z., & Kotadia, H. R. (2021). Effects of Fe, Mn, chemical grain refinement and cooling rate on the evolution of Fe intermetallics in a model 6082 Al-alloy. Intermetallics, 132(December 2020), 1–10.
Li, S. S., Yue, X., Li, Q. Y., Peng, H. L., Dong, B. X., Liu, T. S., Yang, H. Y., Fan, J., Shu, S. L., Qiu, F., & Jiang, Q. C. (2023). Development and applications of aluminum alloys for aerospace industry. Journal of Materials Research and Technology, 27, 944–983.
Mathew, J., Williams, M. A., & Srirangam, P. (2021). X-ray Computed Tomography Studies on Porosity Distribution in Vacuum Induction Cast Al-7Si Alloys. Jom, 73(12), 3866–3872.
Niu, G., Mao, J., & Wang, J. (2019). Effect of Ce Addition on Fluidity of Casting Aluminum Alloy A356. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 50(12).
Niu, G., Wang, Y., Zhu, L., Ye, J., & Mao, J. (2022). Fluidity of casting Al–Si series alloys for automotive light-weighting: a systematic review. In Materials Science and Technology (United Kingdom) (Vol. 38, Issue 13).
Rao, P. S., Gajghat, R. H., Kalbande, V. N., Kumbhalkar, M. A., & Rambhad, K. S. (2023). Optimization of fluidity and mechanical properties of the sand casting A518 alloy by using grey relational analysis method. AIP Conference Proceedings, 2839(1), 20032.
Samuel, A., Zedan, Y., Doty, H., Songmene, V., & Samuel, F. H. (2021). A Review Study on the Main Sources of Porosity in Al-Si Cast Alloys. Advances in Materials Science and Engineering, 2021.
Samuel, E., Samuel, A. M., Doty, H. W., Valtierra, S., & Samuel, F. H. (2025). Highlights on the Role of Fe, Sr, and Solidification Time on Porosity Formation in Al–Si Cast Alloys. International Journal of Metalcasting, 19(3), 1803–1824.
Simões, S. (2025). Advances in the Design and Development of Lightweight Metal Matrix Composites: Processing, Properties, and Applications. Metals, 15(12), 1–35.
Song, D. fu, Wang, S. cheng, Zhao, Y. liang, Liu, S. hong, DU, Y., Kang, Y. hua, Wang, Z., & Zhang, W. wen. (2020). Effect of melt holding on morphological evolution and sedimentation behavior of iron-rich intermetallic phases in Al—Si—Fe—Mn—Mg alloy. Transactions of Nonferrous Metals Society of China (English Edition), 30(1), 1–13.
Sun, Y. (2023). The use of aluminum alloys in structures: Review and outlook. Structures, 57(September), 105290.
Timelli, G., & Bonollo, F. (2007). Fluidity of aluminium die castings alloy. International Journal of Cast Metals Research, 20(6).
Vatankhah Barenji, R. (2022). Casting fluidity, viscosity, microstructure and tensile properties of aluminum matrix composites with different Mg2Si contents. Rare Metals, 41(8).
Wang, Y. Xiao, WU, G. Hua, Zhang, L., Guo, Y. Jie, Tong, X., LI, L. bin, & Xiong, X. Man. (2025). Effect of pouring and mold temperatures on fluidity and hot tearing behavior of cast Al−Li−Cu−Mg−Sc−Zr−Ti alloy. Transactions of Nonferrous Metals Society of China (English Edition), 35(3), 669–683.
Yin, J., Yin, X., Liu, J., Li, S., Liu, Y., & Sun, S. (2026). Low-cost thermal-resistant aluminum alloy wire for electrical purposes without Zr. Materialia, 45(September 2025), 102688.
Yu, W., Li, Y., Jiang, T., Wang, Y., Zhang, B., Li, X., Wang, Z., Xu, G., & Li, J. (2022). Solute inverse segregation behavior in twin roll casting of an Al-Cu alloy. Scripta Materialia, 213(November 2021), 114592.
Zhang, X., Wang, D., Li, X., Zhang, H., & Nagaumi, H. (2021). Understanding crystal structure and morphology evolution of Fe, Mn, Cr-containing phases in Al-Si cast alloy. Intermetallics, 131(October 2020), 107103.
Zhang, X., Wang, D., Zhou, Y., Chong, X., Li, X., Zhang, H., & Nagaumi, H. (2021). Exploring crystal structures, stability and mechanical properties of Fe, Mn-containing intermetallics in Al-Si Alloy by experiments and first-principles calculations. Journal of Alloys and Compounds, 876, 160022.
Zou, G., Chai, Y., Shen, Q., Cheng, T., & Zhang, H. (2022). Analysis of the Fluidity and Hot Tearing Susceptibility of AlSi3.5Mg0.5Cu0.4 and A356 Aluminum Alloys. International Journal of Metalcasting, 16(2).
Zou, G. T., Zhang, H. H., Yang, Y. T., Lu, F. M., Yu, Z. T., & Wang, C. (2020). Effects of Pouring and Mold Temperatures on the Fluidity and Hot Tearing Susceptibility of Al–3.5Si–0.5Mg–0.4Cu Alloy. Transactions of the Indian Institute of Metals, 73(10).
Downloads
Published
How to Cite
Issue
Section
Categories
License
Copyright (c) 2026 Sudarsono, Amir Arifin, Hidayat, La Ode Ahmad Barata, Aminur
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
